Description
Flexible Solar Panel 300W + MPPT Travel Charger 50A Kit is an RV power storage kit using smart Lithium-Iron Phosphate Battery.
This kit comes with the tools necessary for a new system: three Renogy100 Watt 12 Volt Flexible Monocrystalline Solar Panels, one 12V 50A DC-DC On-Board Battery Charger with MPPT, one 20ft 10AWG Solar Adaptor Kit, one 8ft 4AWG Tray Cable,one 20A Solar Connector Waterproof In-Line Fuse Holder w/ Fuse , one pair of branch connectors, two 100Ah 12 Volt Smart Lithium-Iron Phosphate Battery，and one pair of Battery Interconnect Cables . Let's travel in comfort with a vehicle that is both solar powered and drive-charged.
Key Features
Expandable- Designed for expansion, the Renogy 50A DC-DC Battery Charger has a maximum PV input of 25VDC, you can expand your system up to a maximum of 660W.
- The Renogy 100W Flexible Monocrystalline Expansion Kit is the perfect addition for future expansion.
- This 100W solar panel can flex up to 248 degrees, minimizing the mounting and even issues for a curved surface. Where rigid panels are inconvenient to install, get this one.
- Light as 4.2 pounds, this product weighs 1/4 of its rigid counterpart. Travel light with solar, embrace possibilities.
- This Renogy 100W flexible panel is only 0.08 inches thick! It is about 95% thinner than its rigid counterpart, ideal for a stealthy solar setup.
- Rigorously tested, the 100W panel can withstand extreme winds of up to 2400 Pa and snow loads of up to 5400 Pa. Fearless of extreme climates, backup your brave journey.
- Six metal reinforced mounting holes, simple to install. You can also mount it with silicone structural adhesive.
- 【3-phase MPPT Charging Technology】 With Built-in Maximum Power Point Tracking (MPPT), Renogy DC-DC On-Board Battery Charger will charge your service batteries with maximized solar power, providing 3-phase charging (Bulk, Boost and Float) to regulate the whole charging and ensure the batteries will be accurately charged at the correct voltage levels to 100%.
- 【Multiple Protections】Renogy DC-DC On-Board Battery Charger has multiple intelligent protections includes battery isolation, over-voltage protection, battery temperature protection, over-current protection, overheat protection, reverse current protection, solar panel and alternator reverse polarity protection, guaranteeing charging safety and protecting you batteries.
- Pre-drilled holes on the back frame for fast and secure mounting.
- Connects multiple batteries in parallel safely without internal state non-uniformity issues.
- Ultra-Safety. The battery management system (BMS) provides comprehensive protection to the battery and manages the charging/discharging process wisely.
- Uncompromised Quality. State-of-the-art battery cells ensure a lifespan of more than 4000 cycles, 100A continuous discharge current, and a wide range of operation temperature.
- Communication Port. The RJ45 communication ports enable data transmission to meet the needs of different usage scenarios.
- POWERFUL DC-AC.2000W continuous with 4000W peak surge during load start-up. 12V to 115VAC pure sine wave with conversion efficiency >90%, reduces conversion loss.
- SAFE. The built-in Ground-Fault Circuit Interrupter (GFCI) will protect users by de-energizing the circuit when it detects a fault condition. An LED indicator will signal over-load, over-temperature, over-voltage, short-circuit, and under-voltage protection.
- PROTECTS YOUR ELECTRONICS. Advanced pure sine wave technology provides power in a way that will protect and extend the life of your electronics and appliances. The Renogy 2000W 12V Pure Sine Wave Inverter offers quiet operation, with no background buzzing when your electronics are turned on and allows for smooth operation.
- EASY TO USE. Offers a built-in 5V/2.1A USB port, AC outlets and an AC hardwire port. It also comes with a 3tf 4AWG cable and a 19 Ft wired remote included.
- RELIABLE. ETL listed to CSA Standard C22.2 No. 107.1 and UL 458. 1-Year material and workmanship warranty.
Package Includes
|
100 Watt 12 Volt Flexible Mono Solar Panel
3 x |
50A 12V dcc50s DC-DC On-Board Battery Charger with MPPT
1 x |
|
20ft 10AWG Solar Adaptor Kit (Connecting Solar Panels To Charge Controller)
1 x |
8ft 4AWG Tray Cables for 3/8 in Lugs (Connecting Battery to Charge Controller) 1 x |
|
MC4 Waterproof In-Line 30A Fuse Holder
1 x |
2000W 12V Pure Sine Wave Inverter
1 x |
|
100Ah 12 Volt Smart Lithium Iron Phosphate Battery
2 x |
12In 1AWG Copper Battery Interconnect Cable for 5/16In Lugs
2 x |
|
Solar MC4Y2 Branch Connectors MMMF+FFFM Pair
1 x |
|
| 100 Watt 12 Volt Flexible Monocrystalline Solar Panel | DCC50S 12V 50A DC-DC On-Board Battery Charger with MPPT |
|---|---|
| Max Power at STC：100W | System Voltage：12VDC |
| Open Circuit Voltage (VOC)：22.5V | Battery voltage Range：9-16VDC |
| Short Circuit Current (ISC): 5.75A | Maximum Charging Current: 50A |
| Optimum Operating Voltage (VMP): 18.9V | Battery Types: SLD/AGM, GEL, FLD, LISER |
| Optimum Operating Current (IMP): 5.29A | Service Battery Charging Mode: MPPT |
| Operating Temperature:: -40 to +85°C | Charging Efficiency: Up to 97% |
| Dimensions:: 48.0x21.6x0.08in(1219x546x2mm) | Max. Solar Input Voltage: 25V |
| Weight:: 4.2lbs(1.9kg) | Max. Solar Input Power: 660W |
| Alternator Input Voltage: Traditional Alternator: 13.2-16VDC Smart Alternator (Euro 6): 12-16VDC |
|
| Max. Alternator Input Power: 660W | |
| Self-consumption: 60mA | |
| RENOGY 8FT 4AWG TRAY CABLES (PAIR) | Mechanical Specifications |
| Size : 4AWG 8ft | Ground Type: Negative |
| Rating Voltage: : 600/1000V | Terminal Size: M8*1.25 - 10mm |
| Operating Temperature: -40°F to +185°F | Temperature Compensation: -3mV/C/2V |
| 30A Solar Connector Waterproof In-Line Fuse Holder w/ Fuse | Operating Temperature Range: -31°F - 149°F |
| Current Rating: 30A | Storage Temperature Range: -40°F - 176°F |
| Degree of Protection: IP2*/IP67 | Operating / Storage Humidity: 0%-95%, No Condensation |
| Rated Voltage: 1000 V DC | Dimensions: 9.6*5.7*3.0in |
| Test Voltage: 6000V (50Hz,1 min) | Weight: 3.13Ibs |
| Contact Material: Copper, Silver Plated | Communication Protocol: RS485 |
| Temperature Range: -40 to +125°C | |
| 3 TO 1 SOLAR BRANCH CONNECTORS MMMF+FFFM PAIR | |
| Maximum working voltage:DC1000V | Shell Protection degree:IP67 |
| Rated Current:50A | Ambient temperature range:-40°C to +85°C |
| Flame class:UL94-V0 | Safety Level:class Ⅱ |
| Pollution degree:2 | Insertion force:≤50N |
| Contact resistance:≤5mmΩ | Withdrawal force:≥50N |
| Renogy 20ft 10AWG Solar Adaptor Kit (SET) | |
| Size: 10AWG 20ft | |
| Rating Voltage:: 600/1000V | |
| Operating Temperature: -40°F to +185°F | |
| 12V 100AH SMART LITHIUM IRON PHOSPHATE BATTERY | |
| Rated Capacity:100 Ah | Storage Temperature:-13~149℉ / -25~65℃ |
| Nominal Voltage:12.8 V | Insulation Resistance:500V DC, ≥ 10 MΩ |
| Voltage Range:10~14.8 V | Dimensions:11.4 x 6.8 x 7.4 inch / 289 x 172 x 187.5 mm |
| Maximum Continuous Charging Current:50 A | Weight:26 lbs. / 11.8 kg |
| Maximum Continuous Discharging Current:100 A | Protection Rate:IP54 |
| Charge Temperature:32~131°F/ 0~55°C | Communication Port:RJ45 (RS485 Protocol) |
| Discharge Temperature:-4~140°F/ -20~60°C | Connection Method:Parallel |
| Battery Interconnect Cables | |
| Length:12In | Stranding:Class K 30AWG Bare Copper Stranded |
| Size:1AWG | Operating Voltage:600/1000 V |
| Conductor:Tinned Copper | Maximum Operating Temperature:221°F Dry, 167°F Wet |
| Terminal:5/16In Rings Terminals at Both Ends | |
| 2000W 12V Pure Sine Wave Inverter | |
| Inverter Output Specifications | |
| Continuous Output Power:2000W | AC Terminal Block:1 |
| Peak Power Rating:4000W | USB Power Port:5V/2.1A |
| Output Voltage:120V | Power Output Control:AC On/Off Switch, and Remote Control |
| Output Frequency:60 Hz ± 0.1% | Output Waveform:Pure Sine Wave |
| AC Output Sockets:3 | Nominal Efficiency:> 90% |
| Total Harmonic Distortion (THD):< 3% Linear Load < 5% Non-linear Load | |
| Input Specifications: | |
| Nominal Input Battery Voltage:12V | High Voltage Alarm:16V |
| Battery Terminal Size:M8 | Battery Low Shutdown:10.0V ± 0.5V DC |
| Low Battery Alarm:10.5V ± 0.5V DC | Battery Over Voltage Shutdown:16.5V ± 0.5V DC |
| No Load Current Draw:< 2A | |
| Mechanical Specifications | |
| Dimensions:17.8 x 8.6 x 4 in | Cooling Fan:Thermally controlled |
| Weight:11.7 lb | Operating Temperature Range : -4°F - 158°F |
| Certifications | |
| Battery Charger | CE and RoHS compliant |
| FCC Class B Part 15 Compliant | |
| Panel | ISO |
| CE | |
| Battery | UN38.3 |
| MDDS | |
| CE | |
| UL 1642 (Battery Cell) | |
| Inverter | CE |
Warranty Information
| Panels |
25-year power output warranty: 5-year material and workmanship warranty |
| Accessories | 1-year material and workmanship warranty |
| Battery Charger | Material and workmanship warranty----2 Year |
| Battery | Material and workmanship warranty---5 Year |
| Inverter | 1-year material and workmanship warranty |
 |
1.What do I need to complete my off-grid solar power system ?
A solar panel has to be connected to a charge controller to regulate current, and a battery to store the electrical power. You will need adapter kit cables to wire the solar panel(s) and charge controller, and tray cables connecting the charge controller to a deep-cycle battery.
2. What does off-grid and on-grid mean ?
On-grid simply means solar power equipment (array or solar panel) is connected to the electrical grid, while off-grid refers to systems that are not connected to the grid and therefore store the generated power for later use. Off-grid systems are not affected by grid blackouts.
3. Why is my solar panel under producing ?
Solar panel performance may be hindered for a number of reasons. Most commonly environmental conditions such as indirect sunlight, temperature rise, cloudy sky, and dirt and stain build up on the top glass will cause a reduced power output.
4. How should I connect solar panels in my electrical circuit (series vs parallel)
Solar panels can be connected in series or in parallel to meet your electrical circuit size and power demand. Connecting solar panels in series will have the effect of adding up their operating voltage output, while system current output will be the same as that for one panel. While, connecting solar panels in parallel will have a different effect; individual panels operating current output will add up to be the system output current, while system output voltage will be the same as the output voltage of one solar panel. To meet the optimum power output and system rating for your power system, you can use both parallel and series connections.
5. How many solar panels do I need ?
The best way to gauge how many solar panels you need, is to understand and define the power load needed from this system. Power is measured in Watts, and capacity is commonly measured in Watt-hours (multiplying power output in watts by the required number of hours of operation multiplied by a safety factor of 1.5-2). Therefore, it is wise to size your battery bank first based on the minimum required capacity, and accordingly decide how many panels or how much power input is needed.
More questions about your off-grid power system? Learn more from Renogy Learning Center!
